|
Printing like a wire birds nest
|
|
5
|
2181
|
June 2, 2017
|
|
K8400 extruder temp going up and down
|
|
7
|
1055
|
May 25, 2017
|
|
Printquality, backlash
|
|
10
|
1941
|
May 18, 2017
|
|
Overhang angles get worse then better with increasing angle
|
|
1
|
602
|
May 18, 2017
|
|
Issue with little parts
|
|
0
|
672
|
May 15, 2017
|
|
Vertex Resets Suddenly
|
|
1
|
657
|
May 2, 2017
|
|
Filament 1.8mm ABS
|
|
1
|
648
|
April 20, 2017
|
|
Stepper-driver cooling fan
|
|
1
|
590
|
April 14, 2017
|
|
Printer is moving object by Y axis without control
|
|
1
|
671
|
April 11, 2017
|
|
Comparisson printing PLA PETG and ABS filament on the Vertex
|
|
8
|
2451
|
April 5, 2017
|
|
K8400 object moves, when it's small
|
|
1
|
599
|
March 29, 2017
|
|
Problem with structure in 3d printing
|
|
1
|
605
|
March 26, 2017
|
|
Printing object on the edge
|
|
7
|
960
|
March 24, 2017
|
|
Ring printing issues
|
|
6
|
844
|
March 24, 2017
|
|
How do i prevent infill with curaengine 1.0.6
|
|
3
|
694
|
March 23, 2017
|
|
K8400 temperature drop while printing
|
|
3
|
1113
|
March 22, 2017
|
|
After printing a while, no x-axis changes
|
|
5
|
816
|
March 20, 2017
|
|
Blockage in Peek Tube
|
|
11
|
1229
|
March 16, 2017
|
|
[SOLVED]Layer shift, stepper motor problem?
|
|
8
|
4360
|
March 12, 2017
|
|
Step motor rattering very bad
|
|
1
|
613
|
March 12, 2017
|
|
ABS too low adherence
|
|
2
|
735
|
March 9, 2017
|
|
Extruder motor
|
|
3
|
666
|
February 26, 2017
|
|
Heatbed get not at temperature
|
|
10
|
1030
|
February 22, 2017
|
|
Velleman K8400 isolator peek smelt
|
|
2
|
674
|
February 16, 2017
|
|
[SOLVED] K8400 tuning and coarse layer shifting
|
|
3
|
948
|
February 15, 2017
|
|
SOLVED: K8400 erratic printer head movement
|
|
6
|
847
|
February 13, 2017
|
|
Another heater overrun
|
|
1
|
604
|
February 12, 2017
|
|
Abs printing problem
|
|
6
|
911
|
February 12, 2017
|
|
K8400 heaters on uncontrollably (thermal runaway)
|
|
8
|
877
|
February 9, 2017
|
|
Vertical lines/pattern on surface
|
|
0
|
638
|
February 8, 2017
|